感觉这种路子挺对的，官方提供了所有零件的规格和采购地址，乐趣爆炸～准备开搞……

引用:

原帖由 mavefenn 于 2020-9-24 17:04 发表
给个连接或者牌子介绍啊，查了anycubic没看到啊

不好意思哈……
这不是anycubic，是voron 2.4，国内叫沃龙，国外开源的一个方案，官网http://vorondesign.com/
官网上可以选设计方案，选完官方会提供完整的零件清单，从螺丝规格到电线规格列的清清楚楚，相当良心！

250x250版本部件清单

Category	Description	Qty	Notes
Fasteners	M5x40 SHCS	22
	M5x30 BHCS	22
	M3x30 SHCS	25
	M5x10 BHCS	40
	M5x16 BHCS	27
	M5 Hexnut	26
	M5 T-nut HNTAJ5-5	61
	M3 T-nut HNTAJ5-3	104
	M3 Threaded Insert	90
	M3x12 SHCS	23
	M5 1mm Spacer	42
	M2x10 Self-tapping Screw	15
	M3x40 SHCS	28
	M3 Washer	2
	M3x20 SHCS	29
	M3x16 SHCS	14
	M3x8 SHCS	201
	M3 Hexnut	7
	M4 Knurled Nut (DIN 466-B)	4
	M3 Hammer Head T-nuts	47
	M4x6 BHCS	4
	M3x6 BHCS	6
Motion	GT2 20T Pulley (5mm ID 6mm W)	3
	F695 Bearing	20
	GT2 20T Toothed Idler (5mm ID 6mm W)	2
	GT2 20T Toothed Idler (5mm ID 9mm W)	4
	625 Bearing	12
	5x60mm Shaft	4
	GT2 16T Pulley (5mm ID 6mm W)	4
	GT2 80T Pulley (5mm ID 6mm W)	4
	GT2 20T Pulley (5mm ID 9mm W)	4
	GT2 Belt Loop (6mm W) - 188mm	4
	5x30mm Shaft	1
	GT2 Open Belt LL-2GT-9 (9mm wide) - 910mm	4
	BMG Extruder Componnets Kit	1
	Linear Rail MGN9H 300mm	8
	GT2 Open Belt LL-2GT-6 (6mm wide) - 1600mm	2
Electronics	NEMA17 Motor 17HS19-2004S	6
	SPDT KW10 Limit Micro Switch	3
	PL-08N Inductive Probe	1
	E3D V6 Bowden Hotend Kit (24V)	1
	40x40x20 Centrifugal Fan (24V)	1
	40x40x10 Axial Fan (24V)	1
	Mini 12864 Display	1
	Inlet Power Socket IEC320 C14	1
	Keystone CAT6 Insert (Optional)	1
	60x60x20 Fan (24V)	3
	SKR 1.4	2
	TMC2209 Stepper Motor Driver	7
	USB Cable A-male B-male	2
	RaspberryPi 4	1
	Mean Well LRS-200-24 PSU	1
	Mean Well RS-25-5 PSU	1
	Omron G3A-210B-DC5 SSR	1
	DIN Rail Mount Bracket for G3A SSR	1
	BAT85 Diode	1
	C13 Power Cord	1
	Thermal Fuse (120C)	1
	NEMA17 Motor 17HS08-1004S	1
Vibration Management	Rubber Compressor Foot	4
Frame	OpenBuilds Angle Corner Connector	4
	Misumi HFSB5-2020-240	1
	DIN 3 Rails (35mm W) - 370mm	2
	Misumi HFSB5-2020-330	1
	Misumi HFSB5-2020-350	2
	Misumi HFSB5-2020-370-TPW	10
	Misumi HFSB5-2020-430-LCP-RCP	4
Misc	Fume Extractor Carbon Filter Element	1
	4mm Bowden Coupler	1
	Bowden Tube 100mm Piece (For Spool Holder)	2
	3M VHB Tape 5952	1
	Loctite Blue Threadlocker Stick	1
	Mobil EP2 Grease	1
	SuperLube PTFE Grease	1
	Tesa Wire Loom Harness Tape	1
	6x3mm Neodimium Magnet	8
	PTFE Tube (4mm OD 3mm ID) - 1m	1
Cables	Nylon Cable Ties 4"	40
	20AWG Silicone Cable (10ft total)	1
	24AWG Silicone Cable (250ft total)	1
	Spade Crimp Terminal 4.8mm Female	7
	JST XH Connector Plug 4 Position	7
	JST XH Connector Plug 2 Position	6
	MicroFit3 Connector Plug 4 Position	4
	MicroFit3 Connector Plug 3 Position	1
	MicroFit3 Connector Plug 2 Position	2
	MicroFit3 Connector Receptacle 4 Position	4
	MicroFit3 Connector Receptacle 3 Position	1
	MicroFit3 Connector Receptacle 2 Position	2
	JST XH Female Pin	40
	MicroFit3 Female Pin	40
	MicroFit3 Male Pin	40
	VORON XY ZipChain (printed a/b link pairs)	18
	VORON Z ZipChain (printed a/b link pairs)	11
	VORON XY ZipChain (printed ends)	4
	VORON Z ZipChain (printed ends)	2
Panels	Coroplast Sheet - 370x370x4 mm	2
	Coroplast Sheet - 384x404x4 mm	1
	Acrylic Sheet Clear - 192x404x2.5 mm	2
	Acrylic Sheet Clear - 384x404x2.5 mm	2
	Acrylic Sheet Clear - 384x384x2.5 mm	1
Buildplate	3M 468MP Adhesive Sheet - 10"x10"	1
	PEI 0.04" Sheet - 10"x10"	1
	MIC6 5/16" Plate - 10"x10"	1
	Keenovo Silicone AC Heater w/ thermistor - 200x200mm (300W)	1

引用:

原帖由 zj2002ss 于 2020-9-24 17:30 发表
这是玩机党，不是玩3D打印，难点是组装精度和程序调试。
装完后能不能正常打印，还有打印质量的调教都是玩的内容。

实话说我觉得这才是正路，国内老把3D打印机搞得有多low就多low，成本越低越好，好像便宜点就能普及似的……
实际上我觉得这东西短期普及几乎不可能，本来就应该玩精品路线搞点有B格的东西出来才有意思

posted by wap, platform: iPhone

引用:

原帖由 @Alloyo  于 2020-9-24 18:42 发表
现在挤出式的精度咋样了？
貌似激光树脂的精度很高了，准备搞一个做模型

实话说fdm 就那样，打小人肯定不合适，但是平时自己喜欢diy，喜欢自己做点什么的，fdm非常合适

posted by wap, platform: iPhone

引用:

原帖由 @sceic  于 2020-9-24 19:06 发表
不会是8根欧规铝型材要800多的那种方案吧？

已经快3k了，这次买的都是比较好的料

posted by wap, platform: iPhone

引用:

原帖由 @n2  于 2020-9-24 18:24 发表
成本高，有b格不表示要自己从0开始组

其实不冲突，精品化才是正路！