Board logo

标题: [资源分享] 挖个坑 写个 PSC OTG 刷机教程 [打印本页]

作者: yonexhb    时间: 2019-5-31 13:36     标题: 挖个坑 写个 PSC OTG 刷机教程

https://modmyclassic.com/bleemsync/
这是原文


今天PSC 收到以后 晚上刷好 抽空写一下 :)
引用:
BleemSync v1.1 – Installing from fresh

Disclaimer – We are not responsible for any damage caused to your console. Please note that you are installing and using at your own risk!

Download the BleemSync v1.1 zip package to your computer.
Format a USB drive (USB 2.0 preferable) to FAT32 and label it SONY. The format must be FAT32 or ext4.
Extract the zip package to the root of your newly formatted USB.
Make sure your console is unplugged from power.
Insert the USB to controller port 2 on your console and hook the console power back up. Progress updates are displayed on the screen so it is recommended to have the HDMI cord plugged in. It is recommended that while updating you do not have any other usb devices connected to your console. Note: If you have an externally powered usb hub, insert your usb drive into the hub and insert the hub into controller port 2. (Recommended for users with USB power issues)
When the console’s LED is orange, power it on as normal and wait!
The system will create a backup of your existing kernel, recovery, and data partitions. This may take up to 5 minutes. The LED will alternate green and red while this is happening, and the following will be displayed on screen: Screenshot
After the backup has completed the initial payload will be installed to the console. When the payload has finished installing you should see this screen: Screenshot
Once the console has powered off and you see an orange LED. Remove your usb stick and plug it into your computer.
IMPORTANT: Create a backup of your consoles backup files copy them somewhere safe. The backup files are stored in USB:\bleemsync\backup. It is important you keep a copy of these files somewhere safe. They are unique and can only be used on the console that created them. DO NOT DELETE THESE FILES FROM THE USB DRIVE! If they do not exist then the console will re-create them on boot (and any backups made subsequent to this would be of the upgraded BleemSync kernel and not the original one).
Download the custom kernel (LBOOT.EPB) and save it to USB:\bleemsync\update. Safely remove the usb from your computer and plug it back into your console.
Turn on your console. The console will count down from 5 before performing the kernel upgrade. During the upgrade the console will turn off (LED completely off), turn back on (LED flashing green), and then turn off once more.
When the LED has returned to orange the installation of BleemSync is now complete! Turn the console back on and it will now boot to the BleemSync Boot Menu.
Next Steps

Ensure you have created multiple copies of the backup files. The backup files are stored in USB:\bleemsync\backup. It is important you keep a copy of these files somewhere safe as they will be required should you need to revert your console back to stock or recover your console. They are unique and tied to the console that created them. There will be three files:
USB:\bleemsync\backup\LBOOT.EPB
USB:\bleemsync\backup\LBOOT_KERNEL.EPB
USB:\bleemsync\backup\LRECOVERY.EPB
Do not delete these files from the USB drive. If they do not exist then the console will re-create them on boot (and any backups made subsequent to this would be of the upgraded (modified) system and not the original one).

Reformat your USB drive in a better format. exFAT, NTFS and ext4 are all supported. Simply copy the entire contents of your USB drive to your computer, format the drive in the format you want (remember to name the drive SONY), and then copy the contents back to your USB drive. Note however that should you want to restore your kernel (or further upgrade to any future kernel releases) then you will need to reformat you drive into FAT32 or ext4 (or use a secondary usb for the upgrade). The kernel upgrade process is not compatible with NTFS or exFAT
(Optional) Use your OTG cable! Simply connect your USB drive to your OTG cable and start the console as normal. BleemSync will load in the same way that it would when you connect it to controller port 2.

作者: jidatui    时间: 2019-5-31 13:44

posted by wap, platform: Android
PSC不需要刷机,插上U盘就能用。
作者: AzureZH    时间: 2019-5-31 13:47

其实PSC刷机已经很简单了,就是要保存好自己的固件备份文件
作者: yonexhb    时间: 2019-5-31 13:47

大致分为一下几步

0 准备U盘
1 下载整合包[https://classicmodscloud.com/bleemsync/BleemSync1.1.0.zip] 和自制固件[https://classicmodscloud.com/bleemsync/LBOOT.EPB]
2 U盘格式化为 FAT32 或者 ext4 并且改名为 SONY
3 整合包解压放在U盘
4 插入 PSC 2P口启动
5 会自动备份 出三个固件[固件只匹配当前机器]

    USB:\bleemsync\backup\LBOOT.EPB
    USB:\bleemsync\backup\LBOOT_KERNEL.EPB
    USB:\bleemsync\backup\LRECOVERY.EPB

6 拷贝自制固件[LBOOT.EPB] 到 USB:\bleemsync\update 运行
作者: yonexhb    时间: 2019-5-31 13:48

引用:
原帖由 jidatui 于 2019-5-31 13:44 发表
posted by wap, platform: Android
PSC不需要刷机,插上U盘就能用。
家里娃五岁 主要是需要和娃双打 2P口 接U盘 尴尬

就是想要 其中的 OTG 功能
作者: jidatui    时间: 2019-5-31 14:02

posted by wap, platform: Android
引用:
原帖由 @yonexhb  于 2019-5-31 13:48 发表
家里娃五岁 主要是需要和娃双打 2P口 接U盘 尴尬

就是想要 其中的 OTG 功能
随便找个usb hub就可以了,不识别的话就外接个手机充电器,或者一劳永逸的硬改。

本帖最后由 jidatui 于 2019-5-31 14:07 通过手机版编辑
作者: yonexhb    时间: 2019-5-31 14:05

引用:
原帖由 jidatui 于 2019-5-31 14:02 发表
posted by wap, platform: Android
随便找个usb hub就可以了,不识别的话就外接个手机充电器。

本帖最后由 jidatui 于 2019-5-31 14:04 通过手机版编辑  
外接手机充电器可还行

我都试试看吧
作者: jidatui    时间: 2019-5-31 14:10

posted by wap, platform: Android
引用:
原帖由 @yonexhb  于 2019-5-31 14:05 发表
外接手机充电器可还行

我都试试看吧
PSC的usb口电流太低,需要硬改,改了以后什么U盘和hub都能识别。
如果不会硬改,就外接一个手机充电器,效果是一样的,很多hub都可以外接电源。


https://b23.tv/av51638989
作者: yonexhb    时间: 2019-5-31 14:35

引用:
原帖由 jidatui 于 2019-5-31 14:10 发表
posted by wap, platform: Android
PSC的usb口电流太低,需要硬改,改了以后什么U盘和hub都能识别。
如果不会硬改,就外接一个手机充电器,效果是一样的,很多hub都可以外接电源。


https://b23.tv/av51638989
声音好性感
硬了
作者: 泰哥    时间: 2019-6-3 09:24

posted by wap, platform: 小米
这个标记起来
作者: 老五    时间: 2019-6-3 09:33

马克可能用的到
作者: 洛克狼    时间: 2019-6-3 10:19

引用:
原帖由 jidatui 于 2019-5-31 14:10 发表
posted by wap, platform: Android
PSC的usb口电流太低,需要硬改,改了以后什么U盘和hub都能识别。
如果不会硬改,就外接一个手机充电器,效果是一样的,很多hub都可以外接电源。


https://b23.tv/av51638989
改后只是兼容性提高,需要大电流的优盘还是不识别的
作者: yonexhb    时间: 2019-6-3 10:22

目前的进展是 手头几个U盘都不识别

其中一个识别了 结果 bleemsync 固件备份 都失败 我就不敢直接刷 自制固件了

新的U盘下单了

等新U盘 到了 再进一步测试吧
作者: sgasoka    时间: 2019-6-3 10:59


老外推荐的这一款U盘,直接FAT32格式化,拷贝插上就可用,我买了
我自己用的TF加读卡器搞定的
修改USB电流限制很简单,短接俩电阻就行



[ 本帖最后由 sgasoka 于 2019-6-3 11:05 编辑 ]

图片附件: 5bbeb6a4Ne6bb78fb.jpg (2019-6-3 10:59, 28.82 KB) / 该附件被下载次数 14
http://club.tgfcer.com/attachment.php?aid=1069106



图片附件: (2019-6-3 10:59, 66.51 KB) / 该附件被下载次数 13
http://club.tgfcer.com/attachment.php?aid=1069107



图片附件: (2019-6-3 10:59, 62.04 KB) / 该附件被下载次数 9
http://club.tgfcer.com/attachment.php?aid=1069108


作者: yonexhb    时间: 2019-6-3 11:26

引用:
原帖由 sgasoka 于 2019-6-3 10:59 发表
1069106
老外推荐的这一款U盘,直接FAT32格式化,拷贝插上就可用,我买了
我自己用的TF加读卡器搞定的
修改USB电流限制很简单,短接俩电阻就行
1069108
1069107
感谢
作者: AzureZH    时间: 2019-6-3 13:30

我一共换了7、8个U盘/读卡器才认出来,主要是不想拆机

作者: jingly1    时间: 2019-6-4 08:09

posted by wap, platform: VIVO
期待!
作者: abe1007之马甲    时间: 2019-6-4 08:52

我买了力童的miix2的OTG,连在机器电源口确实可以启动,但是U盘认不出。我检查了下刷机的文件夹,备份和刷机内核都在。是我刷写的时候出了什么问题吗?还是我选的OTG有问题呢?U盘没有问题。
作者: 真忘私绵    时间: 2019-7-26 01:20

posted by wap, platform: iPhone
和楼上一样据说要再靠背个文件
作者: djboyx2000    时间: 2019-7-27 19:27

Mark
作者: ziyouren    时间: 2019-8-23 15:28

学习了,感谢~




欢迎光临 TGFC Lifestyle (http://club.tgfcer.com/) Powered by Discuz! 6.0.0